To cast bullets in the field I would dig a Dakota fire hole;
make a wire bail on a 15 oz bean can; put bail on a metal
rod across the fire hole to hang the can down in the fire
hole to melt the wheel weights. I would flux with wax,
stir and pour the metal with a lead dipper; then drop the
bullet from mould into water to quench and harden.
http://www.survivaltopics.com/survival/the-dakota-fire-hole/
http://www.buffaloarms.com/browse.cfm/4,2480.html
http://www.castbullet.com/reload/acast.htm
excerpt Paco Kelly talks about water-quenching bullets
and I have begun to use this method of quickly cooling
bullets cast from wheelweights. If you drop the bullet
into the water straight from the mold, the water cools
the bullet quickly imparting additional hardness to the
new bullet. Hard bullets are good if you are casting for
smokeless powder.
So, if I am casting for my pistols and want hard bullets,
I fill the mold and let the sprue harden. As soon as the
sprue hardens I whack the sprue plate and drop the
sprue on the towel. I then hold the mold over the
water-filled can and drop the bullets directly into the
can. When the bullets are hot, you can hear them
sizzle as they hit the water. end excerpt
Monday, April 27, 2009
Friday, April 24, 2009
B0V bike in the trunk
A cheap and dirty BOV bike in the trunk
--buy an 0ld steel frame bike cheap
--install heavy duty wheelset and airfree tires
--cut t0p tube and d0wntube
--use external sleeve, 0r steel b0lt inside tubes, t0
c0nnect the cut tubes. drill h0les. tw0 b0lts at each end
maybe use allenhead screws?
--disassemble/assemble quickly
This bike has 400 lb GVW.
http://tinyurl.com/55zc5p.
You can equip any frame with
400 lb GVW one speed wheelset.
WHEEL 26x2.125 rear coaster brake, 120g, steel (HD-120)
http://tinyurl.com/55zc5p00-222 Price: $42.00
WHEEL 26x2.125 front, 120-g spokes, steel (HD-120)
Price: $27.00
http://tinyurl.com/cmokpc
www.airfreetires.com
Tell Hugh Waters that you want
the +30% version 0celot and
Sierra Unidirectional. They have
little rolling resistance under
my 280 lbs.
http://www.airfreetires.com/shopping/p-60-26-x-19-ocelot-low-profile-559-premium-hd.aspx
http://www.airfreetires.com/shopping/p-64-26-x-19-sierra-unidirectional-559-premium-hd.aspx
--buy an 0ld steel frame bike cheap
--install heavy duty wheelset and airfree tires
--cut t0p tube and d0wntube
--use external sleeve, 0r steel b0lt inside tubes, t0
c0nnect the cut tubes. drill h0les. tw0 b0lts at each end
maybe use allenhead screws?
--disassemble/assemble quickly
This bike has 400 lb GVW.
http://tinyurl.com/55zc5p.
You can equip any frame with
400 lb GVW one speed wheelset.
WHEEL 26x2.125 rear coaster brake, 120g, steel (HD-120)
http://tinyurl.com/55zc5p00-222 Price: $42.00
WHEEL 26x2.125 front, 120-g spokes, steel (HD-120)
Price: $27.00
http://tinyurl.com/cmokpc
www.airfreetires.com
Tell Hugh Waters that you want
the +30% version 0celot and
Sierra Unidirectional. They have
little rolling resistance under
my 280 lbs.
http://www.airfreetires.com/shopping/p-60-26-x-19-ocelot-low-profile-559-premium-hd.aspx
http://www.airfreetires.com/shopping/p-64-26-x-19-sierra-unidirectional-559-premium-hd.aspx
Wednesday, April 22, 2009
Silent but deadly and other Ed Harris essays
silent but deadly and other Ed Harris essays
http://guns.connect.fi/gow/ed.html
Cast Bullet Basics For Military Surplus Rifles
By C.E. Harris Rev. 9-6-93
FOR THE FULL - NON-CONDENSED VERSION, PICK UP THE NEWEST EDITION OF HANDLOADER'S DIGEST.
Cast bullet loads usually give a more useful zero at practical field ranges with military battle sights than do full power loads. Nothing is more frustrating than a military rifle that shoots a foot high at a hundred yards with surplus ammo when the sight is as low as it will go!
Do NOT use inert fillers (Dacron or kapok) to take up the excess empty space in the case. This was once common practice, but it raises chamber pressure and under certain conditions contributes to chamber ringing. If a particular load will not work well without a filler, the powder is not suitable for those conditions of loading.
Four load classifications from Mattern (1932) cover all uses for the cast bullet military rifle. I worked up equivalent charges to obtain the desired velocity ranges with modern powders, which provide a sound basis for loading cast bullets in any post-1898 military rifle from 7 mm to 8 mm:
1. 125-gr., plainbased "small game/gallery"
900-1000 f.p.s., 5 grains of Bullseye or equivalent.
2. 150-gr. plainbased "100-yd. target/small game",
1050-1250 f.p.s., 7 grs. of Bullseye or equivalent.
3. 150-180-gr. gaschecked "200-yard target"
1500-1600 f.p.s., 16 grs. of #2400 or equivalent.
4. 180-200-gr. gaschecked "deer/600-yard target"
1750-1850 f.p.s., 26 grs. of RL-7 or equivalent.
None of these loads are maximum when used in full-sized rifle cases such as the .30-40 Krag, .303 British, 7.65 Argentine, 7.7 Jap, 7.62x54R or .30-'06. They can be used as basic load data in most modern military rifles of 7 mm or larger, with a standard- weight cast bullet for the caliber, such as 140-170 grains in the 7x57, 150-180 grains in the .30 calibers, and 150-190 grains in the 8 mm. For bores smaller than 7 mm, consult published data.
The "Small Game or Gallery" Load
The 110-115-gr. bullets intended for the .30 carbine and .32-20 Winchester, such as the Lyman #311008, #311359 or #311316 are not as accurate as heavier ones like the #311291. There isn't a readily-available .30 cal. cast small game bullet of the proper 125-130-gr. weight. LBT makes a 130-gr. flat-nosed, GC bullet for the .32 H&R Magnum which is ideal for this purpose. I recommend it highly, particularly if you own a .32 revolver!
The "100-Yard Target and Small Game" Load
I use Mattern's plainbased "100-yard target load" to use up my minor visual defect culls for offhand and rapid-fire 100-yard practice. I substitute my usual gaschecked bullets, but without the gascheck. I started doing this in 1963 with the Lyman #311291. Today I use the Lee .312-155-2R, or the similar tumble-lubed design TL.312-160-2R. Most of my rifle shooting is done with these two basic designs.
Bullets I intend for plainbased loads are blunted using a flatnosed top punch in my lubricator, providing a 1/8" flat which makes them more effective on small game and clearly distinguishes them from my heavier gaschecked loads. This makes more sense to me than casting different bullets. Bullet preparation is easy. I visually inspect each run of bullets and throw those with gross defects into the scrap box for remelting. Bullets with minor visual defects are tumble-lubed in Lee Liquid Alox without sizing, and are used for plain-based plinkers. Bullets which are visually perfect are sorted into groups of +/- 0.5 grain used for 200 yard matches. Gaschecks pressed onto their bases by hand prior running into the lubricator-sizer.
For "gaschecked bullets loaded without the gascheck," for cases like the .303 British, 7.62 NATO, 7.62x54R Russian and .30-'06 I use 6-7 grains of almost any fast burning pistol powder, including, but not limited to Bullseye, W-W231, SR-7625, Green Dot, Red Dot, or 700-X. I have also had fine results with 8 to 9 grains of medium burning rate pistol or shotgun powders, such as Unique, PB, Herco, or SR-4756 in any case of .303 British size or larger.
In the 7.62x39 case use no more than 4 grains of the fast-burning powders mentioned, or 5 grains of the shotgun powders. These make accurate 50-yd. small game loads which let you operate the action manually and save your precious cases. These plinkers are more accurate than you can hold.
Repeated reloading of rimless cases with very mild loads results in the primer blast shoving the shoulder back, unless flash holes are enlarged with a No.39 drill to 0.099" diameter. Cases which are so modified must NEVER be used with full-power loads! ALWAYS identify cases which are so modified by filing a deep groove across the rim with a file and label them clearly to prevent their inadvertent use. For this reason I prefer to do my plainbased practice shooting in rimmed cases like the .30-30, .30-40 rag, .303 British and 7.62x54R which maintain positive headspace on the rim and are not subject to this limitation.
The Harris "Subsonic Target" Compromise
Mattern liked a velocity of around 1250 f.p.s. for his "100-yard target" load, because this was common with the lead-bullet .32-40 target rifles of his era. I have found grouping is best with non-gascheck bullets in military rifles at lower velocities approaching match-grade .22 Long Rifle ammunition. I use my "Subsonic Target" load at around 1050-1100 f.p.s. to replace both Mattern's "small game" and "100-yard target" loads, though I have lumped it with the latter since it really serves the same purpose. Its report is only a modest pop, rather than a crack.
If elongated bullet holes and enlarged groups indicate marginal bullet stability, increase the charge a half grain and try again. If necessary increasing the charge no more than a full grain from the minimum recommended, if needed to get consistent accuracy. If this doesn't work, try a bullet which is more blunt and short for its weight, because it will be more easily stabilized. If this doesn't do the trick, you must change to a gaschecked bullet and a heavier load.
The Workhorse Load - Mattern's "200-Yard Target"
My favorite load is the most accurate, Mattern's so-called "200-yard target load". I expect 10-shot groups at 200 yards, firing prone rapid with sling to average 4-5". I shoot high-Sharpshooter/low-Expert scores across the course with an issue 03A3 or M1917, shooting in a cloth coat, using my cast bullet loads. The power of this load approximates the .32-40, inadequate for deer by today's standards.
Mattern's "200-yard target load" is easy to assemble. Because it is a mild load, soft scrap alloys usually give better accuracy than harder ones such as linotype. Local military collector-shooters have standardized on 16 grains of #2400 as the "universal" prescription. It gives around 1500 f.p.s. with a 150-180-gr. cast bullet in almost any military caliber. We use 16 grains of #2400 as our reference standard, just as highpower competitors use 168 Sierra MatchKings and 4895.
The only common military rifle cartridge in which 16 grains of #2400 provides a maximum load which must not be exceeded is in the tiny 7.62x39 case. Most SKS rifles will function reliably with charges of #2400 as light as 14 grains with the Lee .312-155-2R at around 1500 f.p.s. I designed this bullet especially for the 7.62x39, but it works very well as a light bullet in any .30 or .303 cal. rifle.Cast Bullet Basics For Military Surplus Rifles (cont.)
Sixteen Grains of #2400 Is The Universal Load
The same 16 grain charge of #2400 is universal for all calibers as a starting load. It is mild and accurate in any larger military case from a .30-40 Krag or .303 British up through a .30-'06 or 7.9x57, with standard-weight bullets of suitable diameter for the caliber. This is my recommendation for anybody trying cast bullet loads for the first time in a military rifle without prior load development. I say this because #2400 is not position sensitive, requires no fiber fillers to ensure uniform ignition, and actually groups better when you just stripper-clip load the rifle and bang them off, rather than tipping the muzzle up to position the charge.
Similar ballistics can be obtained with other powders in any case from 7.62x39 to .30-'06 size. If you don't have Hercules #2400 you can freely substitute 17 grains of IMR or H4227, 18 grs. Of 4198, 21 grs. of Reloder 7, 24 grs. of IMR3031, or 25.5 grs. Of 4895 for comparable results. However, these other powders may give some vertical stringing in cases larger than the 7.62x39 unless the charge is positioned against the primer by tipping the muzzle up before firing. Hercules #2400 does not require this precaution. Don't ask me why. Hercules #2400 usually gives tight clusters only within a narrow range of charge weights within a grain or so, and the "universal" 16 grain load is almost always best. Believe me, we have spent a lot of time trying to improve on this, and you can take our word for it.
The beauty of the "200-yard target load" at about 1500 f.p.s. is that it can be assembled with bullets cast from the cheapest inexpensive scrap alloy, and fired all day without having to clean the bore. It ALWAYS works. Leading is never a problem. Once a uniform bore condition is established, the rifle behaves like a .22 match rifle, perhaps needing a warming shot or two if it has cooled, but otherwise being remarkably consistent. The only thing I do after a day's shoot is to swab the bore with a couple of wet patches of GI bore cleaner or Hoppe's, and let it soak until the next match. I then follow with three dry patches prior to firing. It only takes about three foulers to get the 03A3 to settle into tight little clusters again.
"Deer and Long Range Target" Load
Mattern's "deer and 600 yard target load" can be assembled in cases of .30-40 Krag capacity or larger up to the .30-'06 using 18-21 grs. of #2400 or 4227, 22-25 grs. of 4198, 25-28 grs. Of RL-7 or 27-30 grs. of 4895, which give from 1700-1800 f.p.s., depending on the case size. These charges must not be used in cases smaller than the .303 British without cross-checking against published data! The minimum charge should always be used initially, and the charge adjusted within the specified range only as necessary to get best grouping. Popular folklore suggests a rifle barrel must be near perfect for good results with cast bullets, but this is mostly bunk, though you may have to be persistent.
I have a rusty-bored Finnish M28/30 which I have shot extensively, in making direct comparisons with the same batches of loads on the same day with a mint M28 and there was no difference. The secret in getting a worn bore to shoot acceptably is remove all prior fouling and corrosion. Then you must continue to clean the bore "thoroughly and often" until it maintains a consistent bore condition over the long term. You must also keep cast bullet loads under 1800 f.p.s. for hunting, and under 1600 for target work.
A cleaned and restored bore will usually give good accuracy with cast bullet loads if the bullet fits the chamber THROAT properly, is well lubricated and the velocities are kept below 1800 f.p.s. The distinction between throat diameter and groove diameter in determining proper bullet size is important. If you are unable to determine throat diameter from a chamber cast, a rule of thumb is to size bullets .002" over groove diameter, such as .310" for a .30-'06, .312" for a 7.62x54R and .314" for a .303 British.
"Oversized .30s" like the .303 British, 7.7 Jap, 7.65 Argentine, 7.62x39 Russian and frequently give poor accuracy with .30 cal. cast bullets designed for U.S. barrels having .300 bore and .308 groove dimensions, because the part of the bullet ahead of the driving bands receives no guidance from the lands in barrels of larger bore diameter. The quick rule of thumb to checking proper fit of the forepart is to insert the bullet nose first into the muzzle. If it enters to clear up to the front driving band without being noticeably engraved, accuracy will seldom be satisfactory.
The forepart is not too large if loaded rounds can be chambered with only slight resistance, the bullet does not telescope back into the case, or to stick in the throat when extracted without firing. A properly fitting cast bullet should engrave the forepart positively with the lands, and be no more than .001" under chamber throat diameter on the driving bands. Cast bullets with a tapered forepart at least .002" over bore diameter give the best results.
Many pre-WWII Russian rifles of US make, and later Finnish reworks, particularly those with Swiss barrels by the firm SIG, have very snug chamber necks and cannot be used with bullets over .311" diameter unless case necks are reamed or outside turned to .011" wall thickness to provide safe clearance. Bullets with a large forepart like the Lee .312-155-2R or Lyman #314299 work best in the 7.62x54R, because the forcing cones are large and gradual. Standard .30 cal. gaschecks are correct. Finnish 7.62x54R, Russian 7.62x39 and 7.65 Argentine barrels are smaller than Russian 7.62x54R, Chinese 7.62x39, Jap 7.7 or .303 British barrels, and usually have standard .300" bore diameter, (Finnish barrels occasionally are as small as .298") and groove diameters of .310-.3115".
In getting the best grouping with iron sighted military rifles, eyesight is the limiting factor. Anybody over age 40 who shoots iron sights should to equip himself with a "Farr-Sight" from Gil Hebbard or Brownell's. This adjustable aperture for your eyeglass frame was intended for indoor pistol shooters, but it helps my iron sight rifle shooting, and adds about 5 points to my score!
http://guns.connect.fi/gow/ed.html
Cast Bullet Basics For Military Surplus Rifles
By C.E. Harris Rev. 9-6-93
FOR THE FULL - NON-CONDENSED VERSION, PICK UP THE NEWEST EDITION OF HANDLOADER'S DIGEST.
Cast bullet loads usually give a more useful zero at practical field ranges with military battle sights than do full power loads. Nothing is more frustrating than a military rifle that shoots a foot high at a hundred yards with surplus ammo when the sight is as low as it will go!
Do NOT use inert fillers (Dacron or kapok) to take up the excess empty space in the case. This was once common practice, but it raises chamber pressure and under certain conditions contributes to chamber ringing. If a particular load will not work well without a filler, the powder is not suitable for those conditions of loading.
Four load classifications from Mattern (1932) cover all uses for the cast bullet military rifle. I worked up equivalent charges to obtain the desired velocity ranges with modern powders, which provide a sound basis for loading cast bullets in any post-1898 military rifle from 7 mm to 8 mm:
1. 125-gr., plainbased "small game/gallery"
900-1000 f.p.s., 5 grains of Bullseye or equivalent.
2. 150-gr. plainbased "100-yd. target/small game",
1050-1250 f.p.s., 7 grs. of Bullseye or equivalent.
3. 150-180-gr. gaschecked "200-yard target"
1500-1600 f.p.s., 16 grs. of #2400 or equivalent.
4. 180-200-gr. gaschecked "deer/600-yard target"
1750-1850 f.p.s., 26 grs. of RL-7 or equivalent.
None of these loads are maximum when used in full-sized rifle cases such as the .30-40 Krag, .303 British, 7.65 Argentine, 7.7 Jap, 7.62x54R or .30-'06. They can be used as basic load data in most modern military rifles of 7 mm or larger, with a standard- weight cast bullet for the caliber, such as 140-170 grains in the 7x57, 150-180 grains in the .30 calibers, and 150-190 grains in the 8 mm. For bores smaller than 7 mm, consult published data.
The "Small Game or Gallery" Load
The 110-115-gr. bullets intended for the .30 carbine and .32-20 Winchester, such as the Lyman #311008, #311359 or #311316 are not as accurate as heavier ones like the #311291. There isn't a readily-available .30 cal. cast small game bullet of the proper 125-130-gr. weight. LBT makes a 130-gr. flat-nosed, GC bullet for the .32 H&R Magnum which is ideal for this purpose. I recommend it highly, particularly if you own a .32 revolver!
The "100-Yard Target and Small Game" Load
I use Mattern's plainbased "100-yard target load" to use up my minor visual defect culls for offhand and rapid-fire 100-yard practice. I substitute my usual gaschecked bullets, but without the gascheck. I started doing this in 1963 with the Lyman #311291. Today I use the Lee .312-155-2R, or the similar tumble-lubed design TL.312-160-2R. Most of my rifle shooting is done with these two basic designs.
Bullets I intend for plainbased loads are blunted using a flatnosed top punch in my lubricator, providing a 1/8" flat which makes them more effective on small game and clearly distinguishes them from my heavier gaschecked loads. This makes more sense to me than casting different bullets. Bullet preparation is easy. I visually inspect each run of bullets and throw those with gross defects into the scrap box for remelting. Bullets with minor visual defects are tumble-lubed in Lee Liquid Alox without sizing, and are used for plain-based plinkers. Bullets which are visually perfect are sorted into groups of +/- 0.5 grain used for 200 yard matches. Gaschecks pressed onto their bases by hand prior running into the lubricator-sizer.
For "gaschecked bullets loaded without the gascheck," for cases like the .303 British, 7.62 NATO, 7.62x54R Russian and .30-'06 I use 6-7 grains of almost any fast burning pistol powder, including, but not limited to Bullseye, W-W231, SR-7625, Green Dot, Red Dot, or 700-X. I have also had fine results with 8 to 9 grains of medium burning rate pistol or shotgun powders, such as Unique, PB, Herco, or SR-4756 in any case of .303 British size or larger.
In the 7.62x39 case use no more than 4 grains of the fast-burning powders mentioned, or 5 grains of the shotgun powders. These make accurate 50-yd. small game loads which let you operate the action manually and save your precious cases. These plinkers are more accurate than you can hold.
Repeated reloading of rimless cases with very mild loads results in the primer blast shoving the shoulder back, unless flash holes are enlarged with a No.39 drill to 0.099" diameter. Cases which are so modified must NEVER be used with full-power loads! ALWAYS identify cases which are so modified by filing a deep groove across the rim with a file and label them clearly to prevent their inadvertent use. For this reason I prefer to do my plainbased practice shooting in rimmed cases like the .30-30, .30-40 rag, .303 British and 7.62x54R which maintain positive headspace on the rim and are not subject to this limitation.
The Harris "Subsonic Target" Compromise
Mattern liked a velocity of around 1250 f.p.s. for his "100-yard target" load, because this was common with the lead-bullet .32-40 target rifles of his era. I have found grouping is best with non-gascheck bullets in military rifles at lower velocities approaching match-grade .22 Long Rifle ammunition. I use my "Subsonic Target" load at around 1050-1100 f.p.s. to replace both Mattern's "small game" and "100-yard target" loads, though I have lumped it with the latter since it really serves the same purpose. Its report is only a modest pop, rather than a crack.
If elongated bullet holes and enlarged groups indicate marginal bullet stability, increase the charge a half grain and try again. If necessary increasing the charge no more than a full grain from the minimum recommended, if needed to get consistent accuracy. If this doesn't work, try a bullet which is more blunt and short for its weight, because it will be more easily stabilized. If this doesn't do the trick, you must change to a gaschecked bullet and a heavier load.
The Workhorse Load - Mattern's "200-Yard Target"
My favorite load is the most accurate, Mattern's so-called "200-yard target load". I expect 10-shot groups at 200 yards, firing prone rapid with sling to average 4-5". I shoot high-Sharpshooter/low-Expert scores across the course with an issue 03A3 or M1917, shooting in a cloth coat, using my cast bullet loads. The power of this load approximates the .32-40, inadequate for deer by today's standards.
Mattern's "200-yard target load" is easy to assemble. Because it is a mild load, soft scrap alloys usually give better accuracy than harder ones such as linotype. Local military collector-shooters have standardized on 16 grains of #2400 as the "universal" prescription. It gives around 1500 f.p.s. with a 150-180-gr. cast bullet in almost any military caliber. We use 16 grains of #2400 as our reference standard, just as highpower competitors use 168 Sierra MatchKings and 4895.
The only common military rifle cartridge in which 16 grains of #2400 provides a maximum load which must not be exceeded is in the tiny 7.62x39 case. Most SKS rifles will function reliably with charges of #2400 as light as 14 grains with the Lee .312-155-2R at around 1500 f.p.s. I designed this bullet especially for the 7.62x39, but it works very well as a light bullet in any .30 or .303 cal. rifle.Cast Bullet Basics For Military Surplus Rifles (cont.)
Sixteen Grains of #2400 Is The Universal Load
The same 16 grain charge of #2400 is universal for all calibers as a starting load. It is mild and accurate in any larger military case from a .30-40 Krag or .303 British up through a .30-'06 or 7.9x57, with standard-weight bullets of suitable diameter for the caliber. This is my recommendation for anybody trying cast bullet loads for the first time in a military rifle without prior load development. I say this because #2400 is not position sensitive, requires no fiber fillers to ensure uniform ignition, and actually groups better when you just stripper-clip load the rifle and bang them off, rather than tipping the muzzle up to position the charge.
Similar ballistics can be obtained with other powders in any case from 7.62x39 to .30-'06 size. If you don't have Hercules #2400 you can freely substitute 17 grains of IMR or H4227, 18 grs. Of 4198, 21 grs. of Reloder 7, 24 grs. of IMR3031, or 25.5 grs. Of 4895 for comparable results. However, these other powders may give some vertical stringing in cases larger than the 7.62x39 unless the charge is positioned against the primer by tipping the muzzle up before firing. Hercules #2400 does not require this precaution. Don't ask me why. Hercules #2400 usually gives tight clusters only within a narrow range of charge weights within a grain or so, and the "universal" 16 grain load is almost always best. Believe me, we have spent a lot of time trying to improve on this, and you can take our word for it.
The beauty of the "200-yard target load" at about 1500 f.p.s. is that it can be assembled with bullets cast from the cheapest inexpensive scrap alloy, and fired all day without having to clean the bore. It ALWAYS works. Leading is never a problem. Once a uniform bore condition is established, the rifle behaves like a .22 match rifle, perhaps needing a warming shot or two if it has cooled, but otherwise being remarkably consistent. The only thing I do after a day's shoot is to swab the bore with a couple of wet patches of GI bore cleaner or Hoppe's, and let it soak until the next match. I then follow with three dry patches prior to firing. It only takes about three foulers to get the 03A3 to settle into tight little clusters again.
"Deer and Long Range Target" Load
Mattern's "deer and 600 yard target load" can be assembled in cases of .30-40 Krag capacity or larger up to the .30-'06 using 18-21 grs. of #2400 or 4227, 22-25 grs. of 4198, 25-28 grs. Of RL-7 or 27-30 grs. of 4895, which give from 1700-1800 f.p.s., depending on the case size. These charges must not be used in cases smaller than the .303 British without cross-checking against published data! The minimum charge should always be used initially, and the charge adjusted within the specified range only as necessary to get best grouping. Popular folklore suggests a rifle barrel must be near perfect for good results with cast bullets, but this is mostly bunk, though you may have to be persistent.
I have a rusty-bored Finnish M28/30 which I have shot extensively, in making direct comparisons with the same batches of loads on the same day with a mint M28 and there was no difference. The secret in getting a worn bore to shoot acceptably is remove all prior fouling and corrosion. Then you must continue to clean the bore "thoroughly and often" until it maintains a consistent bore condition over the long term. You must also keep cast bullet loads under 1800 f.p.s. for hunting, and under 1600 for target work.
A cleaned and restored bore will usually give good accuracy with cast bullet loads if the bullet fits the chamber THROAT properly, is well lubricated and the velocities are kept below 1800 f.p.s. The distinction between throat diameter and groove diameter in determining proper bullet size is important. If you are unable to determine throat diameter from a chamber cast, a rule of thumb is to size bullets .002" over groove diameter, such as .310" for a .30-'06, .312" for a 7.62x54R and .314" for a .303 British.
"Oversized .30s" like the .303 British, 7.7 Jap, 7.65 Argentine, 7.62x39 Russian and frequently give poor accuracy with .30 cal. cast bullets designed for U.S. barrels having .300 bore and .308 groove dimensions, because the part of the bullet ahead of the driving bands receives no guidance from the lands in barrels of larger bore diameter. The quick rule of thumb to checking proper fit of the forepart is to insert the bullet nose first into the muzzle. If it enters to clear up to the front driving band without being noticeably engraved, accuracy will seldom be satisfactory.
The forepart is not too large if loaded rounds can be chambered with only slight resistance, the bullet does not telescope back into the case, or to stick in the throat when extracted without firing. A properly fitting cast bullet should engrave the forepart positively with the lands, and be no more than .001" under chamber throat diameter on the driving bands. Cast bullets with a tapered forepart at least .002" over bore diameter give the best results.
Many pre-WWII Russian rifles of US make, and later Finnish reworks, particularly those with Swiss barrels by the firm SIG, have very snug chamber necks and cannot be used with bullets over .311" diameter unless case necks are reamed or outside turned to .011" wall thickness to provide safe clearance. Bullets with a large forepart like the Lee .312-155-2R or Lyman #314299 work best in the 7.62x54R, because the forcing cones are large and gradual. Standard .30 cal. gaschecks are correct. Finnish 7.62x54R, Russian 7.62x39 and 7.65 Argentine barrels are smaller than Russian 7.62x54R, Chinese 7.62x39, Jap 7.7 or .303 British barrels, and usually have standard .300" bore diameter, (Finnish barrels occasionally are as small as .298") and groove diameters of .310-.3115".
In getting the best grouping with iron sighted military rifles, eyesight is the limiting factor. Anybody over age 40 who shoots iron sights should to equip himself with a "Farr-Sight" from Gil Hebbard or Brownell's. This adjustable aperture for your eyeglass frame was intended for indoor pistol shooters, but it helps my iron sight rifle shooting, and adds about 5 points to my score!
Thursday, April 16, 2009
can you hide your thermal image?
when you are hunted how will you hide your thermal image?
I don't know. maybe those heavy aluminized space blankets.
thermal rifle scope
http://tinyurl.com/dnc8vu
thermal scope hog hunting
http://www.youtube.com/watch?v=iLp6DQjDjxw
I don't know. maybe those heavy aluminized space blankets.
thermal rifle scope
http://tinyurl.com/dnc8vu
thermal scope hog hunting
http://www.youtube.com/watch?v=iLp6DQjDjxw
Tuesday, April 14, 2009
Holbrook device for Garand
The Holbrook Garand rifle thumb saver is $45.00
postpaid. Please send postal money order
John Holbrook
2015 24th St #57
Bellingham WA 98225
john.holbrook@comcast.net
see Boston's Gun Bible page 11/30
-----------------------------------------------------------------------
The Device is a replacement for the GI op rod catch and it stops automatic bolt release when loading a clip. It also prevents auto clip ejection when the last round is fired.
http://www.biggerhammer.net/manuals/garand/expl-vue.htm
Pls see exploded view Garand
The Holbrook device replaces item 31 oprod catch.
He cut the hook off, and installed a spring on one side.
With it installed, the Garand operates much like the M-14/M1A. When a full clip is inserted into the receiver it will latch, however you must pull and release the bolt handle to charge the top round. It will operate in the normal manner until the last round is fired and the
bolt will lock open but the clip will not eject. To eject the clip you must push the eject button on the receiver...
With an empty clip latched in the receiver, single rounds can be loaded into the clip, 1 through 8. when you have as many as you wish, just pull and release and away you go.......
The rifle is not modified and can be converted back to GI by replacing the Device with the original catch.
I installed it in my Garand. It works exactly as described. I am delighted.
So long as the army is supplying you with unlimited ammo it does not matter if the enbloc clips fly away never to be found. The unreconstructed diehard resister/survivor skulking in the mesquite thickets will appreciate the Holbrook device. It allows him to remove the empty clip and keep it for reloading. That's good because he may not be able to find more .
I was a rifleman in First Platoon Co B 27th Wolfhounds Sep 50 to Sep 51 in Korean War One. The idea that the enemy waits to hear the PING of the ejected enbloc clip to charge your position is utter horseshit.
postpaid. Please send postal money order
John Holbrook
2015 24th St #57
Bellingham WA 98225
john.holbrook@comcast.net
see Boston's Gun Bible page 11/30
-----------------------------------------------------------------------
The Device is a replacement for the GI op rod catch and it stops automatic bolt release when loading a clip. It also prevents auto clip ejection when the last round is fired.
http://www.biggerhammer.net/manuals/garand/expl-vue.htm
Pls see exploded view Garand
The Holbrook device replaces item 31 oprod catch.
He cut the hook off, and installed a spring on one side.
With it installed, the Garand operates much like the M-14/M1A. When a full clip is inserted into the receiver it will latch, however you must pull and release the bolt handle to charge the top round. It will operate in the normal manner until the last round is fired and the
bolt will lock open but the clip will not eject. To eject the clip you must push the eject button on the receiver...
With an empty clip latched in the receiver, single rounds can be loaded into the clip, 1 through 8. when you have as many as you wish, just pull and release and away you go.......
The rifle is not modified and can be converted back to GI by replacing the Device with the original catch.
I installed it in my Garand. It works exactly as described. I am delighted.
So long as the army is supplying you with unlimited ammo it does not matter if the enbloc clips fly away never to be found. The unreconstructed diehard resister/survivor skulking in the mesquite thickets will appreciate the Holbrook device. It allows him to remove the empty clip and keep it for reloading. That's good because he may not be able to find more .
I was a rifleman in First Platoon Co B 27th Wolfhounds Sep 50 to Sep 51 in Korean War One. The idea that the enemy waits to hear the PING of the ejected enbloc clip to charge your position is utter horseshit.
Subscribe to:
Posts (Atom)